2013 MAZDA MAZDA6

STRUCTURE

Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Oh

LATCHES/LOCKS/LINKAGES:DOORS:LATCH

Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.

AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE

Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan),

AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE

Mazda North American Operations (Mazda) is recalling certain 2013 Mazda6 and CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan),

The contact owns a 2013 Mazda Mazda6. The contact stated that the vehicle had been repaired under NHTSA Campaign Number: 18V631000 (Suspension, Structure) where a coating was sprayed on the passenger side lower control arm and the area was drained. After receiving the recall repair, the contact became aware that the vehicle was pulling to the right and the steering wheel was tilted to the left. The front passenger’s side tire was slightly turned inward. The vehicle was taken to a certified mechanic where it was diagnosed and determined that the front cross member on the passenger’s side was rusted, causing several fractures. After inspecting the damaged area, the mechanic confirmed that it was the area that was repaired under recall. The vehicle was taken to the dealer but was not yet diagnosed. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The failure mileage was 67,000.

Mileage: 67,000

The contact owns a 2013 Mazda Mazda6. The contact stated that the vehicle had been repaired under NHTSA Campaign Number: 18V631000 (Suspension, Structure) where a coating was sprayed on the passenger side lower control arm and the area was drained. After receiving the recall repair, the contact became aware that the vehicle was pulling to the right and the steering wheel was tilted to the left. The front passenger’s side tire was slightly turned inward. The vehicle was taken to a certified mechanic where it was diagnosed and determined that the front cross member on the passenger’s side was rusted, causing several fractures. After inspecting the damaged area, the mechanic confirmed that it was the area that was repaired under recall. The vehicle was taken to the dealer but was not yet diagnosed. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The failure mileage was 67,000.

Mileage: 67,000

I JUST BAUGHT A 2013 MAZDA6 THE REAR CRADEL AND CROSS MEMBER WAS COMPLETY RUSTED AWAY ONE MOUNT WAS COMPLETY RUSTED OFF .THE SPRINGS WAS ALMOST READY TO FALL OUT THE BOTTEM OF THE SPRING PURCH .IT LOOKED LIKE IT WAS PULLED OUT OF THE OCEAN WHERE IT HAD STAYED FOR YEARS .I TRIED TO FIND A USED REPLACEMENT OUT OF SEVERAL WE FOUND FROM 10-13 AND GOING THRU NATIONAL SALVAGE PARTS WE CAN NOT FIND ONE THAT WAS NOT RUSTY AWAY ALL THE MAZDA6 FRAMS WERE SO RUSTED THEY COULD NOT BE USED .WHY IS THIS NOT ON THE RECALL LIST IF ALL I COULD FIND ARE RUSTED OUT PARTS THAT IS A SAFTY HAZZARD TO HAVE ON THE ROAD.

I JUST BAUGHT A 2013 MAZDA6 THE REAR CRADEL AND CROSS MEMBER WAS COMPLETY RUSTED AWAY ONE MOUNT WAS COMPLETY RUSTED OFF .THE SPRINGS WAS ALMOST READY TO FALL OUT THE BOTTEM OF THE SPRING PURCH .IT LOOKED LIKE IT WAS PULLED OUT OF THE OCEAN WHERE IT HAD STAYED FOR YEARS .I TRIED TO FIND A USED REPLACEMENT OUT OF SEVERAL WE FOUND FROM 10-13 AND GOING THRU NATIONAL SALVAGE PARTS WE CAN NOT FIND ONE THAT WAS NOT RUSTY AWAY ALL THE MAZDA6 FRAMS WERE SO RUSTED THEY COULD NOT BE USED .WHY IS THIS NOT ON THE RECALL LIST IF ALL I COULD FIND ARE RUSTED OUT PARTS THAT IS A SAFTY HAZZARD TO HAVE ON THE ROAD.

I JUST BAUGHT A 2013 MAZDA6 THE REAR CRADEL AND CROSS MEMBER WAS COMPLETY RUSTED AWAY ONE MOUNT WAS COMPLETY RUSTED OFF .THE SPRINGS WAS ALMOST READY TO FALL OUT THE BOTTEM OF THE SPRING PURCH .IT LOOKED LIKE IT WAS PULLED OUT OF THE OCEAN WHERE IT HAD STAYED FOR YEARS .I TRIED TO FIND A USED REPLACEMENT OUT OF SEVERAL WE FOUND FROM 10-13 AND GOING THRU NATIONAL SALVAGE PARTS WE CAN NOT FIND ONE THAT WAS NOT RUSTY AWAY ALL THE MAZDA6 FRAMS WERE SO RUSTED THEY COULD NOT BE USED .WHY IS THIS NOT ON THE RECALL LIST IF ALL I COULD FIND ARE RUSTED OUT PARTS THAT IS A SAFTY HAZZARD TO HAVE ON THE ROAD.

My car has approx 115,000 miles. I took it to Bass Mazda to have spark plugs and serpentine belt changed simply for maintenance purposes. After leaving dealership my car was pulling to the right. My steering wheel was no longer centered. It also was turned toward the right. Any time I had to hit the brakes the car pulled very hard to right. Long story short it we ended up finding out that my sub frame is very rusted and cracked. My car specifically does not fall into the recall for this issue. When I called mazda to inform them that this may be an issue with other cars the rep was ki d of rude. She just kept telling me I needed to contact the dealership to see what they could do and get cost appraisal. I was simply trying to let them know this could be an issue for other vehicles.

My car has approx 115,000 miles. I took it to Bass Mazda to have spark plugs and serpentine belt changed simply for maintenance purposes. After leaving dealership my car was pulling to the right. My steering wheel was no longer centered. It also was turned toward the right. Any time I had to hit the brakes the car pulled very hard to right. Long story short it we ended up finding out that my sub frame is very rusted and cracked. My car specifically does not fall into the recall for this issue. When I called mazda to inform them that this may be an issue with other cars the rep was ki d of rude. She just kept telling me I needed to contact the dealership to see what they could do and get cost appraisal. I was simply trying to let them know this could be an issue for other vehicles.

2013 Mazda 6 VIN [XXX] 1)Fuel tank leak. yes it is available for inspection 2)Gas leak with danger of fire or explosion. 3) Yes 4) No 5)Yes Reoccurring The 2014 Mazda 6 had a recall for the exact same problem I am having where the tank would overfill or if parked unlevel and it will activate a check engine light and "leak gas" out of the EVAP canister even while driving. The recall covered cars built between October 25, 2012 and May 9, 2013. My car was built 7-19-2012 and the dealer will not fix the issue. I have taken it to a dealer in Cincinnati and they said put a new fuel cap on it which I did. The problem has persisted and has gotten worse. I have taken it to garages where they have merely reset the light and returned it unfixed. I have lived "because of the Covid" with the situation over a year and a half by only filling the tank half full. I have only recently discovered the 2014 had a recall but not the 2013. I have spent over a 1000$ trying to get someone to fix it but no b

was driving on the highway when the check engine light came on. not 10 minutes later, I lost acceleration and steering. managed to get to the shoulder just in time before my car pretty much died. the water light and battery light came on when I came to a stop. mechanic discribes it as 'catastrophic engine failure'. other than the check engine light, there were no other warnings. the temperature gage was normal and there were no weird sounds or smoke. diagnostic readings said a coolant leak lead to the radiator overheating which caused the engine to seize. the freeze frame data says 'P0117 engine coolant temperature sensor 1 circuit low'. I researched that and it said that when 'low', the check engine will come on but there will probably be no other warnings and that the sensor usually needs to be replaced around 100k miles. my vehicle is at 51k miles. currently have 3k in repairs which does not include the cost of an engine.

RELATED TO MAZDA RECALL NUMBER 2818I - FRONT FRAME ROTTING OUT. THEY APPLIED A BANDAID FIX UNDER THE RECALL, TO ONLY 1 SIDE OF THE VEHICLE AND THE PART THEY USED DOES NOT EVEN CONNECT TO THE ACTUAL SUSPENSION PIECES THAT ARE ROTTING OUT OF THE FRAME. IT IS BASICALLY A PLATE TO KEEP THE ROTTING FRAME FROM SEPARATING COMPLETELY ON ONLY 1 SIDE. THE PROBLEM IS THE ENTIRE FRAME IS STILL ROTTING AT A CRAZY EXCESSIVE RATE. I HAVE HAD MANY USED, OLDER VEHICLES AND HAVE NEVER SEEN A CAR SO NEW ALMOST RENDERED UNDRIVABLE DUE TO THE FRAME CONDITION. MY MECHANIC SAID IT SHOULD HAVE ALL BEEN REPLACED GIVEN HOW MUCH CORROSION/RUST IS ON THE ENTIRE FRAME INSTEAD OF ONLY A BRACKET ON ONE SIDE... AND THE FIX THEY PERFORMED IS NOTHING MORE THAN A LIABILITY TREATMENT TO KEEP THE CAR FROM COMPLETELY FALLING APART AND KILLING SOMEONE WHEN THE FRAME FAILS ON THAT SIDE. THE FRAME WAS LEFT IN PLACE AND IS ROTTING FASTER THAN I HAVE EVEN SEEN ON A VEHICLE ESPECIALLY AT LESS THAN 10YEARS OLD AND LESS THAN 100K

Mileage: 81,500

RELATED TO MAZDA RECALL NUMBER 2818I - FRONT FRAME ROTTING OUT. THEY APPLIED A BANDAID FIX UNDER THE RECALL, TO ONLY 1 SIDE OF THE VEHICLE AND THE PART THEY USED DOES NOT EVEN CONNECT TO THE ACTUAL SUSPENSION PIECES THAT ARE ROTTING OUT OF THE FRAME. IT IS BASICALLY A PLATE TO KEEP THE ROTTING FRAME FROM SEPARATING COMPLETELY ON ONLY 1 SIDE. THE PROBLEM IS THE ENTIRE FRAME IS STILL ROTTING AT A CRAZY EXCESSIVE RATE. I HAVE HAD MANY USED, OLDER VEHICLES AND HAVE NEVER SEEN A CAR SO NEW ALMOST RENDERED UNDRIVABLE DUE TO THE FRAME CONDITION. MY MECHANIC SAID IT SHOULD HAVE ALL BEEN REPLACED GIVEN HOW MUCH CORROSION/RUST IS ON THE ENTIRE FRAME INSTEAD OF ONLY A BRACKET ON ONE SIDE... AND THE FIX THEY PERFORMED IS NOTHING MORE THAN A LIABILITY TREATMENT TO KEEP THE CAR FROM COMPLETELY FALLING APART AND KILLING SOMEONE WHEN THE FRAME FAILS ON THAT SIDE. THE FRAME WAS LEFT IN PLACE AND IS ROTTING FASTER THAN I HAVE EVEN SEEN ON A VEHICLE ESPECIALLY AT LESS THAN 10YEARS OLD AND LESS THAN 100K

Mileage: 81,500

RELATED TO MAZDA RECALL NUMBER 2818I - FRONT FRAME ROTTING OUT. THEY APPLIED A BANDAID FIX UNDER THE RECALL, TO ONLY 1 SIDE OF THE VEHICLE AND THE PART THEY USED DOES NOT EVEN CONNECT TO THE ACTUAL SUSPENSION PIECES THAT ARE ROTTING OUT OF THE FRAME. IT IS BASICALLY A PLATE TO KEEP THE ROTTING FRAME FROM SEPARATING COMPLETELY ON ONLY 1 SIDE. THE PROBLEM IS THE ENTIRE FRAME IS STILL ROTTING AT A CRAZY EXCESSIVE RATE. I HAVE HAD MANY USED, OLDER VEHICLES AND HAVE NEVER SEEN A CAR SO NEW ALMOST RENDERED UNDRIVABLE DUE TO THE FRAME CONDITION. MY MECHANIC SAID IT SHOULD HAVE ALL BEEN REPLACED GIVEN HOW MUCH CORROSION/RUST IS ON THE ENTIRE FRAME INSTEAD OF ONLY A BRACKET ON ONE SIDE... AND THE FIX THEY PERFORMED IS NOTHING MORE THAN A LIABILITY TREATMENT TO KEEP THE CAR FROM COMPLETELY FALLING APART AND KILLING SOMEONE WHEN THE FRAME FAILS ON THAT SIDE. THE FRAME WAS LEFT IN PLACE AND IS ROTTING FASTER THAN I HAVE EVEN SEEN ON A VEHICLE ESPECIALLY AT LESS THAN 10YEARS OLD AND LESS THAN 100K

Mileage: 81,500

THE LOW BEAM HEADLIGHTS ARE SO DIM YOU BARELY CAN SEE ANYTHING OFTEN I HAVE TO TURN ON HIGH BEAM LIGHTS

Mileage: 140,000

TL* THE CONSUMER OWNS A 2013 MAZDA MAZDA6. THE CONSUMER STATED THAT THE DRIVER'S SIDE REAR VIEW MIRROR WAS FROSTED OVER. THE CONSUMER STATED THAT IT WAS VERY DIFFICULT TO SEE APPROACHING VEHICLE. THE VEHICLE WAS TAKEN TO BROWNS MAZDA LOCATED AT 5625 CENTRAL AVE, TOLEDO, OH 43615, (419)531-0151, TO BE INSPECTED. THE CONTACT WAS INFORMED THAT THE VEHICLE WAS NOT SUBJECTED TO A RECALL. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT CONTACTED NOR INFORMED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 50,000. *AS

Mileage: 50,000

MY 2013 MAZDA 6 HAVE SOME BRAKE RELATED ISSUES, I WAS ABLE TO HEAR THE VACCUM OR AIR LEAKAGE NOISE WHILE APPLYING BRAKES. CAR TAKES LONGER DISTANCE TO STOP OR AT TIMES IT KEEPS ROLLING AT THE TIME OF HARD BRAKING. TOOK IT TO LOCAL MAZDA DEALERSHIP AND FOUND OUT ITS THE BRAKE BOOSTER LEAKING AND NEEDS TO BE REPLACED WHICH ESTIMATES AROUND $600. I WAS TRYING TO FIND ANSWERS ONLINE AND LOOKS LIKE MAZDA HAD THE SAME ISSUES WITH OTHER MODELS TOO FROM 2011 MODELS. I NEED TO KNOW IF THIS IS A SAFETY CONCERN AND MAZDA SHOULD BE EXTENDING THEIR SAFETY WARRANTY OFR THESE KNOWN ISSUES OR DEFECTIVE PARTS.

Mileage: 68,000

THE DASHBOARD ON THE PASSENGER SIDE OF MY MAZDA 6 2013 IS MELTING AND IS VERY STICKY. TODAY AS I WAS DRIVING I STARTED TO NOTICE A GLARE FROM WHERE THE STICKY MELTING PART IS AND IT STARTED OBSTRUCTING MY VISION.

Mileage: 5

MANUFACTURERS RECALL NUMBER 1317F. NHTSA RECALL 18V-018 AND MANUFACTURERS RECALL NUMBER 70131. NHTSA RECALL 13V42500. FIRST ONE IS AIR BAG ON PASSENGER SIDE AND THE OTHER IS MAZDA 6 DOOR LATCH MOUNTING SCREWS.

MANUFACTURERS RECALL NUMBER 1317F. NHTSA RECALL 18V-018 AND MANUFACTURERS RECALL NUMBER 70131. NHTSA RECALL 13V42500. FIRST ONE IS AIR BAG ON PASSENGER SIDE AND THE OTHER IS MAZDA 6 DOOR LATCH MOUNTING SCREWS.

I TOOK MY VEHICLE TO DEALER FOR A RECALL ON THE CROSSMEMBER MY VEHICLE IS FROM NEW YORK IT'S A 2013 AND MY HOLE CROSSMEMBER LOOKS LIKE THE CAR IS FROM THE 90 THEIR IS RUST EVERYWHERE AND I LIFTED MY VEHICLE TODAY AND SAW A PART ON TOP OF A PART WHEN THEY SHOULD OF REPLACED THE HOLE CROSSMEMBER I KNOW IT'S FREE BUT INSTEAD OF PUTTING ONE PICE ONTOP OF ONE PICE WHY NOT REPLACE THE HOLE THING ALSO THEY KEPT MY CAR FOR 2 DAYS JUST TO PUT THAT PICE WHEN IT'S JUST 4 BOLTS

I TOOK MY VEHICLE TO DEALER FOR A RECALL ON THE CROSSMEMBER MY VEHICLE IS FROM NEW YORK IT'S A 2013 AND MY HOLE CROSSMEMBER LOOKS LIKE THE CAR IS FROM THE 90 THEIR IS RUST EVERYWHERE AND I LIFTED MY VEHICLE TODAY AND SAW A PART ON TOP OF A PART WHEN THEY SHOULD OF REPLACED THE HOLE CROSSMEMBER I KNOW IT'S FREE BUT INSTEAD OF PUTTING ONE PICE ONTOP OF ONE PICE WHY NOT REPLACE THE HOLE THING ALSO THEY KEPT MY CAR FOR 2 DAYS JUST TO PUT THAT PICE WHEN IT'S JUST 4 BOLTS