Total Complaints
7006 filings
FORD FUSION · model year
7006 NHTSA complaints, 169 crash reports, and 13 active recalls for this specific cohort.
NHTSA overall rating
Not crash-tested
New Car Assessment Program
The 2010FORDFUSION carries 7006 consumer safety complaints in NHTSA's Office of Defects Investigation database for this specific model-year cohort. Within that volume, owners reported 169 crashes, 16 fires, 104 injuries, and 3 fatalities. No NCAP 5-star crash-test rating is available for this model year in the federal database.
Component-level analysis is where model-year complaints become actionable: the top complaint category for the 2010 FUSION is steering with 1636 filings, followed by power train (809) and vehicle speed control (789). Concentration in one or two component groups is the classic signature of a systemic defect; a flat distribution usually reflects normal aging, warranty complaints, or isolated build-plant variability. This model year has 13 active recall campaigns, which means the manufacturer is obligated to remedy the covered defect at no charge for the life of the vehicle — the full NHTSA campaign numbers are listed below.
NHTSA currently has 3 investigation files overlapping the 2010 FUSION. Owners comparing this cohort against neighboring years should pair the counters above with the complaint-by-year trend on the parent model page — a spike in a single year often tracks to a platform refresh, a new transmission supplier, or an updated ECU calibration. Use the related-complaint feed below to read raw owner narratives before deciding whether any pattern here affects your specific use case.
Total Complaints
7006 filings
Crashes Reported
169 reports
Source
NHTSA ODI
Federal complaints database
Above median complaint volume — review patterns below.
| Component | Count |
|---|---|
| STEERING | 1636 |
| POWER TRAIN | 809 |
| VEHICLE SPEED CONTROL | 789 |
| ENGINE | 699 |
| AIR BAGS | 589 |
| FUEL/PROPULSION SYSTEM | 484 |
| SERVICE BRAKES | 432 |
| ELECTRICAL SYSTEM | 318 |
| FUEL SYSTEM, GASOLINE | 214 |
| ELECTRONIC STABILITY CONTROL (ESC) | 144 |
| UNKNOWN OR OTHER | 134 |
| WHEELS | 120 |
| SERVICE BRAKES, HYDRAULIC | 94 |
| ENGINE AND ENGINE COOLING | 85 |
| POWER TRAIN:AUTOMATIC TRANSMISSION | 83 |
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever register
EQUIPMENT
Ford Motor Company (Ford) is recalling certain all weather driver side accessory floor mats sold for use in model year 2006-2011 Ford Fusion and Mercury Milan, 2006 Lincoln Zephyr, and 2007-2011 Lincoln MKZ vehicles manufactured November 9, 2007, through October 31, 2010. The affected floor mats ma
FUEL SYSTEM, GASOLINE:STORAGE:AUXILLARY TANK
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not op
POWER TRAIN:AUTOMATIC TRANSMISSION
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, MILAN, AND ESCAPE VEHICLES MANUFACTURED FROM FEBRUARY 27, THROUGH MARCH 26, 2010. THE PARK ROD GUIDE RETENTION PIN MAY NOT HAVE BEEN PROPERLY INSTALLED WHICH FAILS TO CONFORM TO THE REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEF
SEATS:FRONT ASSEMBLY:RECLINER
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, EXPLORER, EXPLORER SPORT TRAC, AND MERCURY MILAN AND MOUNTAINEER VEHICLES MANUFACTURED BETWEEN DECEMBER 15, 2009 THROUGH FEBRUARY 3, 2010 EQUIPPED WITH FRONT SEAT MANUAL RECLINERS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR
SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not
AIR BAGS:FRONTAL
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain air bag inflator and/or module replacement service parts that may have been used as part of a collision repair. The parts include certain driver-side air bag inflators and/or modules, designed to fit 2005-2014 Ford Mustang and Mustang GT500. It also i
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Vir
AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to
WHEELS:LUGS/NUTS/BOLTS/STUDS
FORD IS RECALLING CERTAIN MODEL YEAR 2010-2011 FORD FUSION AND MERCURY MILAN VEHICLES EQUIPPED WITH 17 INCH STEEL WHEELS AND BUILT FROM APRIL 1, 2009, THROUGH APRIL 30, 2009, AND FROM DECEMBER 1, 2009, THROUGH NOVEMBER 13, 2010. THE WHEEL STUDS MAY FRACTURE, POTENTIALLY CAUSING A WHEEL TO SEPARATE.
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Vi
AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket tha
The brakes went almost completely out- having to push the pedal all the way to the floor. All ABS and braking lights illuminated in the dash. There is limited stopping power. The car has become undriveable, even after replacing the HCU and abs system. The dealership has been unable to reprogram the brakes. This exact issue falls under recall 19s54, but Ford claims my problem does not meet the requirements- despite my vehicle having been assembled at the same facility (Hermosilla) and within the same date range as the recalled vehicles. I have receipts and documents to show all attempts at fixing the issue.
The brakes completely failed pressed pedal all the way down! My son almost died! The brake pads are new!
The power steering has failed and the rack and pinion needs replacement. Altho there was a recall they will not honor me to fix Bec they said it was over mileage. This is a safety concern bec the vehicle cannot be driven safely without power steering. It can cause you not to be able to turn fast enough or move from on coming traffic. I almost hit another vehicle trying to turn onto road. Have had vehicle looked at and was told it's not safe to drive until fixed
The contact owns a 2010 Ford Fusion. The contact stated that after refueling the vehicle, there was a strong fuel odor entering the cabin of the vehicle that lingered for days. The contact's grandson then discovered that fuel was leaking from the rear driver side of the vehicle. The contact continued driving the vehicle, and the vehicle shut off while driving 50 MPH on the highway. The contact restarted the vehicle, and the check engine warning light illuminated on the instrument panel. The contact coasted the vehicle while in neutral(N) to a safe area. The vehicle was towed to an independent mechanic who discovered a crack in the fuel tank and a defective purge valve. Upon investigation, the contact's grandson discovered NHTSA Campaign Number: 15V793000 (Fuel System, Gasoline), which was linked to the failure. The dealer was notified about the failure, and the contact was informed that the vehicle was not included in the recall. The manufacturer was not notified of the failure. The ve
Mileage: 160,000
The contact owns a 2010 Ford Fusion. The contact stated while at a red traffic light, the brake pedal was depressed and travelled down to the floorboard. No warning lights were illuminated. The vehicle was taken back to the residence, and a dealer was contacted. The dealer made the contact aware of NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic); however, the VIN was not included. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and confirmed that there was a recall associated with the failure. The failure mileage was approximately 90,000.
Mileage: 90,000
Ford claims no recall but my Hydralic:antilock/traction control/electronic limited slip control unit/module. My petal is sinking. Did an ABS bleed and problem continues. Could this part be in my car and I just havenât got a recall
I am reporting a serious safety defect in my vehicle. While driving, the power steering suddenly failed without any warning, resulting in complete loss of steering control. At the same time, the brake warning light, ABS light, and traction control light illuminated, suggesting possible failure of critical braking and stability systems. This incident placed my safety and the safety of others at immediate risk, as the vehicle could not be steered properly and essential safety features may have been disabled. The problem persists, as the vehicle continues to have no functioning power steering and the warning lights remain on. The defective components are available for inspection, and the issue has been reproduced consistently since the initial failure. Given the severity of this malfunction and the danger it poses, I am requesting that a recall be issued to address this defect.
I am reporting a serious safety defect in my vehicle. While driving, the power steering suddenly failed without any warning, resulting in complete loss of steering control. At the same time, the brake warning light, ABS light, and traction control light illuminated, suggesting possible failure of critical braking and stability systems. This incident placed my safety and the safety of others at immediate risk, as the vehicle could not be steered properly and essential safety features may have been disabled. The problem persists, as the vehicle continues to have no functioning power steering and the warning lights remain on. The defective components are available for inspection, and the issue has been reproduced consistently since the initial failure. Given the severity of this malfunction and the danger it poses, I am requesting that a recall be issued to address this defect.
Unintended acceleration event. Entered vehicle, put my foot on the brake, cranked it, held in that position while seatbelting. Engine had a VERY loud revving sound. Within seconds vehicle moving backwards on its own. Foot still on the brake, had not touched gas pedal, had not touched gear shifter, and was still sitting straight forward with my foot on the brake and confirmed gear shifter in park. The car quickly accelerated backwards faster and brake pedal had no effect on stopping or slowing vehicle. Went approx. 30â across parking lot and only stopped because we hit truck parked behind us. Quickly turned off engine and removed keys. Shifter still shows Park. Careful driver. No history of accidents. I found there were several thousand reported events of unintended acceleration (Ford vehicles 2002 to 2010). Ford tried to explain many as driver error or floor mat touching the gas pedal. My mat was clipped down, as designed, with no all-weather mat on top of them, and my
Unintended acceleration event. Entered vehicle, put my foot on the brake, cranked it, held in that position while seatbelting. Engine had a VERY loud revving sound. Within seconds vehicle moving backwards on its own. Foot still on the brake, had not touched gas pedal, had not touched gear shifter, and was still sitting straight forward with my foot on the brake and confirmed gear shifter in park. The car quickly accelerated backwards faster and brake pedal had no effect on stopping or slowing vehicle. Went approx. 30â across parking lot and only stopped because we hit truck parked behind us. Quickly turned off engine and removed keys. Shifter still shows Park. Careful driver. No history of accidents. I found there were several thousand reported events of unintended acceleration (Ford vehicles 2002 to 2010). Ford tried to explain many as driver error or floor mat touching the gas pedal. My mat was clipped down, as designed, with no all-weather mat on top of them, and my
Unintended acceleration event. Entered vehicle, put my foot on the brake, cranked it, held in that position while seatbelting. Engine had a VERY loud revving sound. Within seconds vehicle moving backwards on its own. Foot still on the brake, had not touched gas pedal, had not touched gear shifter, and was still sitting straight forward with my foot on the brake and confirmed gear shifter in park. The car quickly accelerated backwards faster and brake pedal had no effect on stopping or slowing vehicle. Went approx. 30â across parking lot and only stopped because we hit truck parked behind us. Quickly turned off engine and removed keys. Shifter still shows Park. Careful driver. No history of accidents. I found there were several thousand reported events of unintended acceleration (Ford vehicles 2002 to 2010). Ford tried to explain many as driver error or floor mat touching the gas pedal. My mat was clipped down, as designed, with no all-weather mat on top of them, and my
When Applying Brakes the Brake Pedal application of Foot Pressure Travels to the Floor before Slowing the Vehicle. Can the Manufacturer Repair this Safety Problem emmediately ?
So this has happened three times in the span of a year. When applying the brakes the brake pedal it would go to the floor and several dash lights would come on(service advance trac, wrench light, abs light and parking brake light). As this would happen, we would pull off as safely and quickly as possible and shut the car off. But once we start the car again, everything is fine. When this situation happens, there is a very very high possibility of hitting someone. With doing research and talking to a local mechanic. It is doing the exact same thing as the Safety Recall 19S54 Certain 2006-2010 Model Year Fusion/Milan/MKZ/Zephyr Vehicles Equipped with Anti-brakes. HCU failure. But running my VIN it does not show it being recalled but my vehicle is a 2010 Fusion hybrid.
The contact owns a 2010 Ford Fusion. The contact stated that while his son was driving at an undisclosed speed and making a turn, the vehicle lost power steering functionality, and almost cause a crash. The driver was able to manually turn the steering wheel and returned to the residence. The message "Power Steering Assist Fault" was displayed. The vehicle was not diagnosed or repaired by a dealer or an independent mechanic. The manufacturer was notified of the failure and referred the contact to the dealer for assistance. The failure mileage was unknown.
Brake pedal goes to floor and stopping time is poor. Brake inspection leads to fault as possibly master cylinder or HCU. Master cylinder replaced and issue not resolved. The date range and manufacturing location matches NHTSA recall 19V904000 related to HCU valve issue but my VIN is not indicated. The vehicle is from the Hermosillo plant inside the date ranges indicated.
The contact owns a 2010 Ford Fusion. The contact stated that while driving and approaching a stop sign, the brake pedal was depressed; however, the vehicle failed to slow down as intended. The brake pedal was pumped several times for the vehicle to slow down. The vehicle was pulled over to the side of the road and parked. The vehicle was then towed to an independent mechanic, where it was determined that a valve in the junction box needed to be replaced. The vehicle was repaired, but the failure reoccurred 20 days later. The vehicle was then towed to the same independent mechanic, where it was diagnosed, and determined that the ABS junction block and module needed to be replaced. The vehicle was not repaired because the manufacturer had no parts available. The manufacturer was not notified of the failure. The failure mileage was approximately 112,000.
Mileage: 112,000
Was driving down parkway when came up on my exit it was hard to make the turn to even go up. The exit ramp the power steering light and the advanced track light and brake system. Light all came on flashing across the message screen one after another. Thank god I was able to get vehicle pulled over to shoulder and had it towed home. Also needs airbags replaced due to recall! I have contacted two local Ford dealers trying to get an appointment. Also messaged one through their website. On the phone calls I was placed on hold until the phone to shut off. Tried to call back and they just said please hold and put me right back on hold and Iâve never received a message back.
Was driving down parkway when came up on my exit it was hard to make the turn to even go up. The exit ramp the power steering light and the advanced track light and brake system. Light all came on flashing across the message screen one after another. Thank god I was able to get vehicle pulled over to shoulder and had it towed home. Also needs airbags replaced due to recall! I have contacted two local Ford dealers trying to get an appointment. Also messaged one through their website. On the phone calls I was placed on hold until the phone to shut off. Tried to call back and they just said please hold and put me right back on hold and Iâve never received a message back.
Was driving down parkway when came up on my exit it was hard to make the turn to even go up. The exit ramp the power steering light and the advanced track light and brake system. Light all came on flashing across the message screen one after another. Thank god I was able to get vehicle pulled over to shoulder and had it towed home. Also needs airbags replaced due to recall! I have contacted two local Ford dealers trying to get an appointment. Also messaged one through their website. On the phone calls I was placed on hold until the phone to shut off. Tried to call back and they just said please hold and put me right back on hold and Iâve never received a message back.
On [XXX] when leaving a shopping center parking lot, the brake system suddenly failed. I was able to press hard on the foot brake to stop the vehicle near the middle of the intersection. I pulled over to a parking space and replicated the issue. The car was towed to West 40 Auto Care on 284 Montvue Lane in Frederick, MD. Today, they told me they could not fix the issue. I made an appointment with the Ford Motor Company on 1 Waverly Drive for 9/15. I drove the car home slowly (about 1 mile) with the emergency lights on and going about 10 mph. Pressing hard on the foot brake will slowly stop the car. ABS icon and Service Advance Trac appear on the dashboard. Yesterday, the brake and wrench lights were also on. The footbrake does not go all the way to the floor. This issue is of course dangerous and might have caused an issue if I had to brake suddenly on a busy road at a higher speed. The issue appears to correspond with the link at [XXX] and summarized at [XXX] . I did no
Data as of 2025. Sources: NHTSA Office of Defects Investigation (ODI) complaints database, NHTSA recall campaign API, NHTSA NCAP crash-test ratings, and NHTSA FARS for fatality cross-reference.
Read our methodology — how this data is sourced, computed, and verified.