2025 FORD BRONCO

SERVICE BRAKES, HYDRAULIC:POWER ASSIST:ELECTRIC:CONTROL MODULE:SOFTWARE

Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of p

SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT

Ford Motor Company (Ford) is recalling certain 2025 Bronco vehicles. The front upper control arm ball joint nut may be missing or tightened improperly, allowing the front upper control arm to detach from the knuckle assembly.

SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT

Ford Motor Company (Ford) is recalling certain 2024 Ranger, and 2024-2025 Bronco vehicles. The front upper control arm ball joint nut may not have been installed or tightened properly, allowing the front upper control arm to detach from the knuckle assembly.

ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL

Ford Motor Company (Ford) is recalling certain 2025-2026 Bronco and Bronco Sport vehicles. The Instrument Panel Cluster (IPC) may fail at startup.

POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:VALVES/VALVE BODY

Ford Motor Company (Ford) is recalling certain 2024-2025 F-150, Bronco, 2024 Ranger, 2025 Mustang, Explorer, and Aviator vehicles. The transmission valve body may have been machined incorrectly, which can cause reverse gear failure, or unexpected forward movement in reverse or neutral gear.

LATCHES/LOCKS/LINKAGES:DOORS:LOCK

Ford Motor Company (Ford) is recalling certain 2025 Bronco four-door vehicles. The left-hand rear door may be able to be opened from inside the vehicle when the child safety lock is in the "ON" position.

AIR BAGS:FRONTAL

Ford Motor Company (Ford) is recalling certain 2025 Bronco vehicles. The active vent flap on the passenger side may prevent the air bag from deploying as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protec

VISIBILITY:WINDSHIELD

Ford Motor Company (Ford) is recalling certain 2025 Bronco and Ranger vehicles. During manufacturing, the windshield may not have been properly bonded to the vehicle, allowing it to detach in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Stand

SUSPENSION:FRONT:CONTROL ARM:LOWER ARM

Ford Motor Company (Ford) is recalling certain 2024-2025 Bronco vehicles. The front lower control arm fasteners may not have been tightened properly, allowing the control arm to detach from the frame.

SEATS:CRITICAL FASTENERS

Ford Motor Company (Ford) is recalling certain 2025 Ranger and Bronco vehicles. The bolts that secure the driver's seat frame to the body may be loose or missing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 207, "Seating Systems."

SUSPENSION:FRONT:CONTROL ARM:UPPER BALL JOINT

Ford Motor Company (Ford) is recalling certain 2024-2025 Bronco and Ranger vehicles. The front upper control arm ball joint fastener may be missing or tightened improperly, allowing the front upper control arm to detach from the knuckle assembly.

BACK OVER PREVENTION:SOFTWARE

Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.

ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE)

Ford Motor Company (Ford) is recalling certain 2025 Ranger, Lincoln Nautilus, Mustang, Maverick, Explorer, Escape, Lincoln Corsair, Bronco Sport, and Bronco vehicles. The exhaust gas recirculation (EGR) valve may fail, resulting in an unexpected loss of drive power.

SERVICE BRAKES, HYDRAULIC:POWER ASSIST:ELECTRIC:CONTROL MODULE

Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of p

on Jan 15, 2025. A cold start for the Bronco, putting in reverse, the vehicle lurched back and to the hard right, uncommanded acceleration at a high rate of speed, steering locked up, brakes locked up, tires spinning, engine revving causing the bronco to smash into the exterior of my home garage area. Then, shifting to drive, the vehicle again lurched, uncommanded acceleration hard to the left now, steering locked up, brakes locked up, tires spinning engine revving traveling 20-30 feet crashing into the electrical box coming to rest on top of it. Numerous faults showing multiple systems malfunctioning causing this incident.

on Jan 15, 2025. A cold start for the Bronco, putting in reverse, the vehicle lurched back and to the hard right, uncommanded acceleration at a high rate of speed, steering locked up, brakes locked up, tires spinning, engine revving causing the bronco to smash into the exterior of my home garage area. Then, shifting to drive, the vehicle again lurched, uncommanded acceleration hard to the left now, steering locked up, brakes locked up, tires spinning engine revving traveling 20-30 feet crashing into the electrical box coming to rest on top of it. Numerous faults showing multiple systems malfunctioning causing this incident.

on Jan 15, 2025. A cold start for the Bronco, putting in reverse, the vehicle lurched back and to the hard right, uncommanded acceleration at a high rate of speed, steering locked up, brakes locked up, tires spinning, engine revving causing the bronco to smash into the exterior of my home garage area. Then, shifting to drive, the vehicle again lurched, uncommanded acceleration hard to the left now, steering locked up, brakes locked up, tires spinning engine revving traveling 20-30 feet crashing into the electrical box coming to rest on top of it. Numerous faults showing multiple systems malfunctioning causing this incident.

I have experienced three total brake failures in my 2025 Ford Bronco. During the most recent incident on 2-18-2026 the brake pedal traveled completely to the floorboard, requiring extreme force and multiple pumps to stop the vehicle. This appears to be the exact failure described in Ford Recall 25S77 (NHTSA Campaign 25V488) regarding the Electronic Brake Booster (EBB) module. The vehicle was presented to Suntrup Ford twice previously for this issue, but the defect was not corrected. I am reporting a life-threatening safety failure. After February 18th 2026 brake failure I had bronco towed to Suntrup Ford in Kirkwood Missouri and that's where it will stay. I am too frightened to drive it again.

Structural crack in molded in color roof compromising the integrity of vehicle roof.

Loss of braking. Note weather was cold in single digits Fahrenheit and midly snowy. I drove my 2025 Ford Bronco that was purchased in Octorber about 20 minutes to drop off my child at daycare. Going into the daycare I turned to Slippery/4A mode. After about 5 minutes inside I pulled out and switched back to Normal/2H mode. Less than half a mile later I got multiple warnings that the brakes, EBB, collision detect, and ABS had faulted, and I should service now. I only had the electronic parking brake available. I was able to use it and engine braking with my manual transmission to get to off the road to a parking lot, although I did also receive a parking brake overheat fault the turn before getting into the parking lot. I shut the vehicle off without the parking brake on. I turned it back on and the dash warning lights all disappeared after a few seconds. Brake function returned and I drove it to a Ford service center about 1 mile away. They were not able to reproduce the problem or fin

Loss of braking. Note weather was cold in single digits Fahrenheit and midly snowy. I drove my 2025 Ford Bronco that was purchased in Octorber about 20 minutes to drop off my child at daycare. Going into the daycare I turned to Slippery/4A mode. After about 5 minutes inside I pulled out and switched back to Normal/2H mode. Less than half a mile later I got multiple warnings that the brakes, EBB, collision detect, and ABS had faulted, and I should service now. I only had the electronic parking brake available. I was able to use it and engine braking with my manual transmission to get to off the road to a parking lot, although I did also receive a parking brake overheat fault the turn before getting into the parking lot. I shut the vehicle off without the parking brake on. I turned it back on and the dash warning lights all disappeared after a few seconds. Brake function returned and I drove it to a Ford service center about 1 mile away. They were not able to reproduce the problem or fin

Loss of braking. Note weather was cold in single digits Fahrenheit and midly snowy. I drove my 2025 Ford Bronco that was purchased in Octorber about 20 minutes to drop off my child at daycare. Going into the daycare I turned to Slippery/4A mode. After about 5 minutes inside I pulled out and switched back to Normal/2H mode. Less than half a mile later I got multiple warnings that the brakes, EBB, collision detect, and ABS had faulted, and I should service now. I only had the electronic parking brake available. I was able to use it and engine braking with my manual transmission to get to off the road to a parking lot, although I did also receive a parking brake overheat fault the turn before getting into the parking lot. I shut the vehicle off without the parking brake on. I turned it back on and the dash warning lights all disappeared after a few seconds. Brake function returned and I drove it to a Ford service center about 1 mile away. They were not able to reproduce the problem or fin

While slowly backing into our home garage, the vehicle accelerated brakes were not working and smashed into the side of the house, put the car in drive to move it. It accelerated forward over correcting and drove into our power box and came to a halt. No brakes were working and the wheels/steering locked up.

While slowly backing into our home garage, the vehicle accelerated brakes were not working and smashed into the side of the house, put the car in drive to move it. It accelerated forward over correcting and drove into our power box and came to a halt. No brakes were working and the wheels/steering locked up.

While slowly backing into our home garage, the vehicle accelerated brakes were not working and smashed into the side of the house, put the car in drive to move it. It accelerated forward over correcting and drove into our power box and came to a halt. No brakes were working and the wheels/steering locked up.

While driving, after a missed downshift that causes engine bogging, the vehicle experiences a loss of engine power. The engine remains running but will not produce usable torque and will not rev above approximately 800 RPM, despite clutch disengagement and selecting the correct gear. Holding the clutch fully depressed does not immediately restore power; instead, after approximately 4 seconds, the engine stalls or cycles/resets, after which normal operation resumes. The condition persists until the vehicle nearly stops, the engine stalls, or the ignition is cycled. This has occurred in traffic and adverse weather conditions and is repeatable.”

While driving, after a missed downshift that causes engine bogging, the vehicle experiences a loss of engine power. The engine remains running but will not produce usable torque and will not rev above approximately 800 RPM, despite clutch disengagement and selecting the correct gear. Holding the clutch fully depressed does not immediately restore power; instead, after approximately 4 seconds, the engine stalls or cycles/resets, after which normal operation resumes. The condition persists until the vehicle nearly stops, the engine stalls, or the ignition is cycled. This has occurred in traffic and adverse weather conditions and is repeatable.”

While driving, after a missed downshift that causes engine bogging, the vehicle experiences a loss of engine power. The engine remains running but will not produce usable torque and will not rev above approximately 800 RPM, despite clutch disengagement and selecting the correct gear. Holding the clutch fully depressed does not immediately restore power; instead, after approximately 4 seconds, the engine stalls or cycles/resets, after which normal operation resumes. The condition persists until the vehicle nearly stops, the engine stalls, or the ignition is cycled. This has occurred in traffic and adverse weather conditions and is repeatable.”

Description of Incident: > While driving in freezing drizzle/sleet conditions in northern Minnesota, the factory-installed LED headlights on my 2025 Ford Bronco became obscured by ice buildup within 15 minutes of driving. ​The Safety Issue: > the LED headlights do not produce sufficient heat to melt frozen precipitation. This resulted in a degradation of forward visibility during nighttime driving, creating a safety hazard. I was forced to pull over repeatedly on a high-speed roadway to manually scrape ice from the lenses. ​Request: > I am reporting this as a design defect for vehicles sold in northern climates. The lack of a heating element or de-icing mechanism in the standard LED equipment makes the vehicle unsafe for nighttime driving during freezing weather with high humidity conditions.

Accident Statement – Instrument Panel Cluster Failure & Collision While driving my 2025 Ford Outerbanks, the Instrument Panel Cluster (IPC) screen suddenly went completely black without warning. At the time of the malfunction, I was attempting to merge into traffic on my left with my left turn signal activated. Simultaneously, an 18-wheeler in the lane beside me was merging to his right. The sudden loss of my IPC screen meant I could not see my speedometer, warning indicators, safety messages, or any visibility cues needed to safely judge traffic speed and spacing. This created an immediate hazardous situation and made it extremely difficult to manage both my own speed and the surrounding traffic patterns. As I recognized the danger, I attempted to brake and avoid a collision. During this moment, my steering wheel began to shake slightly—possibly due to the lane-keeping or lane-safety system responding. Despite my efforts to correct and avoid impact, the 18-wheeler collided with

Accident Statement – Instrument Panel Cluster Failure & Collision While driving my 2025 Ford Outerbanks, the Instrument Panel Cluster (IPC) screen suddenly went completely black without warning. At the time of the malfunction, I was attempting to merge into traffic on my left with my left turn signal activated. Simultaneously, an 18-wheeler in the lane beside me was merging to his right. The sudden loss of my IPC screen meant I could not see my speedometer, warning indicators, safety messages, or any visibility cues needed to safely judge traffic speed and spacing. This created an immediate hazardous situation and made it extremely difficult to manage both my own speed and the surrounding traffic patterns. As I recognized the danger, I attempted to brake and avoid a collision. During this moment, my steering wheel began to shake slightly—possibly due to the lane-keeping or lane-safety system responding. Despite my efforts to correct and avoid impact, the 18-wheeler collided with

Accident Statement – Instrument Panel Cluster Failure & Collision While driving my 2025 Ford Outerbanks, the Instrument Panel Cluster (IPC) screen suddenly went completely black without warning. At the time of the malfunction, I was attempting to merge into traffic on my left with my left turn signal activated. Simultaneously, an 18-wheeler in the lane beside me was merging to his right. The sudden loss of my IPC screen meant I could not see my speedometer, warning indicators, safety messages, or any visibility cues needed to safely judge traffic speed and spacing. This created an immediate hazardous situation and made it extremely difficult to manage both my own speed and the surrounding traffic patterns. As I recognized the danger, I attempted to brake and avoid a collision. During this moment, my steering wheel began to shake slightly—possibly due to the lane-keeping or lane-safety system responding. Despite my efforts to correct and avoid impact, the 18-wheeler collided with

Driving in sub-freezing temperatures with snow/rain falling and slush on the road, the headlights iced over with thick slush and ice and reduced visibility to dangerous levels requiring me to pull off the road and chip off the ice putting myself in a dangerous situation being on the side of the road during a storm.

The slave Cylinder failed causing the clutch to not fully disengage burning out the clutch at only 783 miles on the vehicle. Ford headquarters claims driver misuse, dealership disagrees at such low mileage.